Plaster / Stucco One-Coat Stucco EIFS Direct Applied Vents Ultra Lath ® Drywall Parts & Pieces Gutter & Siding
   
 Join us on Facebook: Facebook
Sealant & Caulk

Sheathing

DEFS

EIFS

Stucco

Product Description:
PVC vents for stucco, plaster and modified stucco systems were developed by PLASTIC COMPONENTS, INC. Their purpose is to provide architects and contractors with a rust-free, damage resistant, economical alternative to metal vents. These products come standard with 1/8" (3 mm) vent holes (except for our Clog-Free Soffit Vents, which are 1/4" diameter). They are manufactured with high-impact resistant, lead free PVC and conform to ASTM standards D1784 and C1063. All products shall be third party tested to meet ASTM standard D4216-99 and be Canadian Code Compliant. All products are listed by ITS/Warnock Hersey.

Basic Use:
Vents can be applied to ULTRA-LATH®, metal lath, wood base sheathing products, expanded polystyrene, gypsum sheathing, cement sheathing products and any other code approved substrate. They are designed to allow a proper free flow of air, reducing the build-up of uncirculated air in attics or areas that do not have air handling systems. Consult product sheets for air flow guides.

Installation:
Installation should be in accordance with accepted industry standards and local building codes. Connector clips are included.

Weather Resistance:
Ultraviolet Sunlight: Plasticizers and similar chemicals which can migrate to the surface are not present in the PVC formulas used in the manufacturing of PLASTIC COMPONENTS, INC. products covered in this section.

Low Temperatures: All materials will gradually harden as temperatures change. PVC compounds used by PLASTIC COMPONENTS, INC. are formulated to withstand these changes.

Coefficient of Expansion and Contraction: PVC products are weaker than the materials to which they are attached and the plaster in which they are embedded. PLASTIC COMPONENTS, INC. products are designed with perforated flanges and “eyebrows” which provide positive bonding of stucco to the product and substrates to which they are attached. They become part of the building and will move with the wall, subsequently they are not free to express their coefficient of expansion or contraction.

Availability & Cost:
PLASTIC COMPONENTS, INC. vents are generally lower in cost than aluminum and are competitive with most galvanized products. All products are available from regional warehouses which supply your local wholesale distributor.

Specification:
A short form CSI specification is printed on each product sheet and a product description is included to assist you in the proper selection. A copy of the ASTM standard specification is available upon request.

Maintenance:
PVC products have a built in resistance to damage and will return to their original shape when subjected to normal impact. There is no transmission of shock, which means damage is localized to the point of impact. Repairs can be made by returning the product to its original shape and reapplying finish to the damaged area.

Caulking: Use a high grade acrylic based product with a fine tip nozzle. Do not clog holes

Painting: No special preparation necessary.

Physical Characteristics:
Material Description: All products are manufactured from PVC compounds conforming to ASTM D1784-97, cell classification 13244C.

Physical Properties ASTM Test at 0°F (-18°C) at 72°F (22°C)
Tensile Strength, psi D638 8,100 5,900
Tensile Modulus, psi D638 425,000 360,000
Flexural Strength, psi D790 16,500 11,200
Flexural Modulus, psi D790 497,000 415,000
Izod Impact (ft-lbs/in) D256 1.1 3.4
Heat Distortion Temp      
       °F 254 psi D648   160°F (71°C)
Coefficient of Linear Thermal      
       Expansion (in/in° x 105) D696   3.45
E-84 Fire Tunnel Test      
       Flame Spread     18
       Fuel Contribution     ND
       Smoke Density @ 35 Mils     250
       Fire Rating     Class A
Reaction to Stucco or Plaster     None

Warranty:
PLASTIC COMPONENTS, INC. warrants that the product contained herein as manufactured by PLASTIC COMPONENTS, INC., when properly applied and used in and for the manner which they are manufactured in accordance with ASTM standards D1784 and C1063 shall be free from defects and will perform as stated. PLASTIC COMPONENTS, INC. sole responsibility under this warranty shall be for replacement of material only and excluding any labor or installation cost, and for material that is manufactured by PLASTIC COMPONENTS, INC. which has been deemed defective through manufacturing only, and not product which has been damaged during installation, or improperly installed.

Technical Service:
For additional assistance or information please call 1-800-327-7077 or contact your local sales representative.

 
Home | About The Company | What's New | Technical Data | Installation Instructions | Sales Representatives | Contact Us
Plaster/Stucco | One-Coat Stucco | Drywall | EIFS | Direct Applied | ULTRA-LATH® | Parts & Pieces | Gutter & Siding | Related Items
Industry Links