Plaster / Stucco One-Coat Stucco EIFS Direct Applied Vents Ultra Lath ® Drywall Parts & Pieces Gutter & Siding
   
 Join us on Facebook: Facebook
ULTRA-LATH® PLUS
Drip Edge
Sealant & Caulk
Custom Products
Z Flashing
IN-BOX
ULTRA-LATH®
Corner Beads
Vents
ULTRA-TRAC® Intersections
Slip Joint/Expansion Joint
Screeds
ULTRA-TRAC® Reveal System
Control Joints
Casing Beads

"V" Control Joint

Application
Should be used in any application where a surface area is more than 144 square feet. The wide flange allows for more "keying" of the stucco. The "eyebrows" allow for the stucco to key to the "V". Vertical joints should be attached to a stud where necessary.

Specification
Control Joints shall be Plastic Components, Inc. #_______. All exterior accessories shall be of PVC material conforming to ASTM standards D1784, C1063 and D4216-99. They shall be used where specified by the architect and installed per industry standards.

 
Download PDF InstructionsDownload Installation Instructions Download PDF Data SheetDownload Data Sheet Download CAD DrawingDownload CAD Drawing (MASONRY) Download CAD Drawing in PDF format Download PDF Format CAD (MASONRY)

20383/8" (10 mm)"V" control joint, 4-1/8" (111 mm) overall width with perforated flanges.35
20501/2" (13 mm)35
20585/8" (16 mm)35
20753/4" (19 mm)30
20787/8" (22 mm)25
21001" (25 mm)20
10' (3 m) lengths

All butt joints, intersections and ends shall be caulked at the time of installation using an elastomeric sealant, such as Plastic Components' Ultra-TechT (PC-ULTW).

It is recommended that PVC products be used for all exterior exposures.

Floor Line Control Bead w/Drip Edge

Application
For use as a horizontal control joint and a moisture control device where two dissimilar materials, such as wood and concrete, meet. (e.g. First floor concrete block construction and wood frame second floor). It allows moisture to migrate away from the wall. The unique drip edge prevents migrating moisture from entering the v-groove of the control joint.

Specification
Floor Line Control Bead w/Drip Edge shall be Plastic Components, Inc. #________. All exterior accessories shall be of PVC material conforming to ASTM standards D1784, C1063, and D4216. They shall be used where specified by the architect and installed per industry standards.

 
Download PDF Spec SheetDownload Spec Sheet Download PDF Data SheetDownload Data Sheet

2078-507/8" (22 mm) x 1/2" (12 mm)Control Bead w/Drip Edge 3-1/2" (89 mm) unpunched nailing flange.15
2078-587/8" (22 mm) x 5/8" (16 mm)15
2078-787/8" (22 mm) x 7/8" (22 mm)15
2078-78UP7/8" (22 mm) x 7/8" (22 mm)Completely unpunched control bead with drip edge. 3-1/2" (89 mm)15
10' (3 m) Lengths

All butt joints, intersections and ends shall be caulked at the time of installation using an elastomeric sealant, such as Plastic Components' Ultra-TechT (PC-ULTW).

It is recommended that PVC products be used for all exterior exposures.

Factory Assembled Intersections for Floor Line Control Bead

Application
Factory Assembled Intersections for Floor Line Control Bead reduce labor in the field and provide a better quality finish.

Specification
Factory Assembled Intersections for Floor Line Control Bead shall be Plastic Components Inc. #_____. All exterior accessories shall be of PVC material conforming to ASTM standards D1784, C1063 and D4216. They shall be used where specified by the architect and installed per industry standards.

 
Download PDF Data SheetDownload Data Sheet

2078-50AIC7/8" (22 mm) x 1/2" (13 mm)Factory Assembled Inside and Outside Corner Intersections, 7/8" (22 mm) Floor Line Control Bead.15
2078-50AOC7/8" (22 mm) x 1/2" (13 mm)15
2078-58AIC7/8" (22 mm) x 5/8" (16 mm)15
2078-58AOC7/8" (22 mm) x 5/8" (16 mm)15


All butt joints, intersections and ends shall be caulked at the time of installation using an elastomeric sealant, such as Plastic Components' Ultra-TechT (PC-ULTW).

It is recommended that PVC products be used for all exterior exposures.

Inside Corner Control Joint

Application
Inside Corner Control Joint relieves stress and cracking caused by expansion and contraction in the inside angles of walls and ceilings.

Specification
Inside Corner Control Joint shall be Plastic Components Inc. #_____. All exterior accessories shall be of PVC material conforming to ASTM standards D1784, C1063 and D4216. They shall be used where specified by the architect and installed per industry standards.

 
Download PDF Data SheetDownload Data Sheet

2050-IC1/2" (13 mm)Inside Corner Control Joint35
2058-IC5/8" (16 mm)35
2075-IC3/4" (19 mm)30
2078-IC7/8" (22 mm)30
10' (3 m) lengths

All butt joints, intersections and ends shall be caulked at the time of installation using an elastomeric sealant, such as Plastic Components' Ultra-TechT (PC-ULTW).

It is recommended that PVC products be used for all exterior exposures.

Factory Assembled Intersections "V" Control Joint

Application
Use to reduce labor in the field and provide a better quality finish.

Specification
Control Joint Intersections shall be Plastic Components Inc. #_____. All exterior accessories shall be of PVC materials conforming to ASTM standards D1784, C1063 and D4216. They shall be used where specified by the architect and installed per industry standards.

 

Click To Enlarge

Click To Enlarge
Download PDF Data SheetDownload Data Sheet

2050-AIC1/2" (13 mm)Factory Assembled Intersections "V" Control Joint for Inside Corners (IC), Outside Corners (OC), Tees (T) and Crosses (C).25
2050-AOC1/2" (13 mm)25
2050-AT1/2" (13 mm)25
2050-AC1/2" (13 mm)25
2058-AIC5/8" (16 mm)25
2058-AOC5/8" (16 mm)25
2058-AT5/8" (16 mm)25
2058-AC5/8" (16 mm)25
2075-AIC3/4" (19 mm)25
2075-AOC3/4" (19 mm)25
2075-AT3/4" (19 mm)25
2075-AC3/4" (19 mm)25
2078-AIC7/8" (22 mm)25
2078-AOC7/8" (22 mm)25
2078-AT7/8" (22 mm)25
2078-AC7/8" (22 mm)25
2100-AIC1" (25 mm) 25
2100-AOC1" (25 mm) 25
2100-AT1" (25 mm) 25
2100-AC1" (25 mm) 25


All butt joints, intersections and ends shall be caulked at the time of installation using an elastomeric sealant, such as Plastic Components' Ultra-TechT (PC-ULTW).

It is recommended that PVC products be used for all exterior exposures.

"M" Control Joint

Application
This popular "M" design not only provides control of substrate movement but also gives the appearance of an narrow reveal. Removable tape keeps the "V" clean during installation.

Specification
"M" Control Joint shall be Plastic Components Inc. #_______. All exterior accessories shall be of PVC material conforming to ASTM standards D1784, C1063 and D4216. They shall be used where specified by the architect and installed per industry standards.

 
Download PDF Data SheetDownload Data Sheet Download CAD DrawingDownload CAD Drawing (MASONRY) Download CAD Drawing in PDF format Download PDF Format CAD (MASONRY)

20251/4" (6 mm)"M" control joint with removable tape has perforated flanges.50
2138XS3/8" (10 mm) "M" control joint with removable tape has perforated flanges.50
2150X1/2" (13 mm)"M" control joints, 1/2" (13 mm) with removable tape. Larger perforated flanges with two rows of holes.40
2158X5/8" (16 mm)40
2175X3/4" (19 mm))30
2178X7/8" (22 mm)30
2100X1" (25 mm)20
10' (3 m) Lengths • "F" series also available. Add prefix "F" to the product number e.g. Product F2150X

All butt joints, intersections and ends shall be caulked at the time of installation using an elastomeric sealant, such as Plastic Components' Ultra-TechT (PC-ULTW).

It is recommended that PVC products be used for all exterior exposures.
 
Home | About The Company | What's New | Technical Data | Installation Instructions | Sales Representatives | Contact Us
Plaster/Stucco | One-Coat Stucco | Drywall | EIFS | Direct Applied | ULTRA-LATH® | Parts & Pieces | Gutter & Siding | Related Items
Industry Links